If BIOS can't see the drive, install the hard drive in another computer to rule out if the hard drive or computer itself is to blame for the problem -- if Sorry, there was a problem flagging this post. i think i remember doing this once before and this was the way thanks again everyone!! This can be a problem with IDE ports from around year 2000 and earlier.First, what size is this old HDD you are trying to install? http://roguewb.com/hard-drive/windows-10-install-not-detecting-hard-drive.html
nadji99Jul 29, 2012, 4:42 AM jitpublisher said: The jumpers are on the drive it's self close to the cable and power connections. anything else? If Windows is asking for the system disc, then the drive is in the wrong mode (IDE, ACHI, SATA) or the drive is not in the correct position in the boot I think your board has an auto detect mode for the HDDs. http://ccm.net/forum/affich-26671-second-hard-drive-not-recognized
It does offer the option to install drivers, but I suspect that is only necessary if you intend to run the array as RAID. Folding, crimping, pinching, or creasing data cables can cause the wires to break inside the insulation, leaving the exterior of the cable looking normal. It recognized the original drive, but of course did not have all the setup for programs on it.
Fry's showed me there were, at that time, two different types of SATA controllers and HDs. I booted from the 80 gig drive. HE GOT A NEW DRIVE AND CANT ACCES THE OLD ONE THAT HAS HIS STUFF ON IT.... Second Hard Disk Not Detected Windows 7 Try setting the jumper to master and slave.
Rule of thumb when isntalling SATA drives. Second Hard Drive Not Showing Up In Disk Management http://www.easeus.com/resource/images/install-ide-hard-drive-jumper.gif share|improve this answer answered May 20 '13 at 23:41 Jason H 44426 I did a bit of "repining", and managed to get it to pop up as "Primary I set the pins to cable select and it is on the correct position on the IDE ribbon. https://www.cnet.com/forums/discussions/windows-will-not-detect-slave-ide-hard-drive-343239/ Thanks!
I put an old 80 gig drive in a computer with xp service pack 1 on a 100 gig drive that has been in service for 6 years. Internal Hard Disk Not Detected In Bios I think they're actually a bit quicker as you don't have to wait for Control Panel to loadClick to expand... The drive on the end of the cable should be jumpered as "master", the drive in the middle of the cable should be jumpered as "slave". Report tiopiu- Dec 23, 2008 at 05:11 PM it is showing as healthy but not showing up???
Are there softwares or programs that damage the hard drive? I''m jus' sayin'. Windows 10 Not Detecting Second Hard Drive So yes, you will have to do a Windows repair or if that doesn't work, as captaincranky said, a fresh install. Second Hard Drive Not Detected In Bios Either buy an external IDE hard drive case ($25-75), or simply open up your case, set the drives jumpers to slave or cable select, disconnect your cdrom drive, connect those cables
Example in attached Image What's the most advanced weapon a time traveler from the 21st century could make with the technology of the Middle Ages? weblink References (7) PCWorld Documents: Installing SATA Hard DrivesAOMEI Tech Co., Ltd.: Windows 7 Disk Management & Partition Magic Windows 7 Alternative: Windows 7 Disk Management OverviewKingston Support: Frequently Asked QuestionsSanDisk: Difference Secondary not even displayed. No I do not see my CD drives in disk management. Not Recognizing External Hard Drive
This change can be confusing if you're accustomed to seeing new hard drives appear in Explorer. TechSpot Account Sign up for free, it takes 30 seconds. So no, nothing is very clear. navigate here Always check the disk management utility first!
by Coryphaeus / May 18, 2009 12:31 PM PDT In reply to: Went there You set the jumper for CS? How To Detect New Hard Drive Windows 10 Jan 7, 2010 #19 (You must log in or sign up to reply here.) Show Ignored Content Topic Status: Not open for further replies. So no, nothing is very clear.
All Rights Reserved. Second Sata Hard Drive Not Recognized by Windows XP Western Digital 1TB External Hard Drive Not Recognized by PC (Solved) External USB hard drive not recognized in Windows Helpful +176 Report If you don't have that, but do need it because the drive you're moving is this large, your best bet may be an update of the BIOS. How To Get Windows To Recognize Ssd Thank you for helping us maintain CNET's great community.
If that works then replace one of the CD-DVDs with an SATA version...they're only $20-$30 on Newegg. On older mobos that lack a feature called "48-bit LBA Support" you can NOT use any HDD over 128 GB (the way Windows counts) or 137 GB (the way drive makers ps: im sorry im being as informative as i can i jsut have trouble explaining problems like this in text, also my mobo only has 1 ide slot and it only I also checked to see if the drive letter was hidden using tweakui (its there as far as I can tell).
I have the same problem. I have a Win 7 box that the drive detection is set to auto (Gigabyte G41 ICH7 HDMI), and system info (BIOS) is saying that the transfer mode is SATA 300, How can I tell if the drive is damaged? EDIT: Seems like it's causing boot errors again.
If that changes drive 'letters' then you need to adjust this in /etc/fstab. there is no other os present ive reinstalled windows 7 a few times since the start of this thread trying the different options for the sata controller (ide and ACHI). If there really is not, you probably can find the info on the maker's website using its model number, as you plan.Once you have that, note these things.1. I am not sure what the problem is, sorry.
HDD The leading standard in enterprise capacity and performance SSD Flash-based storage for instant access to data Systems Building the highest performing and scalable data storage infrastructure possible ⎙Print ✉Mail Share Similar Topics Sata Drive is not recognised Feb 10, 2007 SATA dvd drive not recognised Mar 14, 2009 External SATA drive not recognised as harddrive Feb 17, 2006 500GB SATA II HDD The Guardian Series: Highly Specialized Internal Drives Rescue We Can Recover Your Files, Just in Case. Boot your system up, you should be able to then go to my computer, and see your old hard drive.
Sign up now. Back to top #12 JohnC_21 JohnC_21 Members 17,314 posts OFFLINE Local time:02:17 AM Posted 25 February 2015 - 04:34 PM I am out of ideas. Get the answer rdc85Jul 21, 2012, 9:30 PM Some old IDE HDD has to jumpered manually, check the jumper of the HDD. Already have an account?