You can use basic drives to maintain existing spanning, mirroring, and striping configurations and to delete these configurations. Log In or Register to post comments Don on Jan 24, 2001 i used your artricle on drive letter assigning, it was written clearly and was exactly the info i was Disk Administrator will create an equal-sized partition in the free space for the mirror.The same drive letter is used for both partitions of a mirror set. You can use the free space in the extended partition to create multiple logical drives, or you can use all or part of it when creating volume sets or other kinds this contact form
When you're finished, restart the computers. This documentation is archived and is not being maintained. Using a RAID system enables you to set up the best disk array design to protect your system. If the drive has large sector sizes, you'll need to reformat before converting.
No, create an account now. A vital tool for protecting a network's data is the use of a REDUNDANT ARRAY OF INEXPENSIVE DISKS (RAID). Just select the areas you want to combine, and choose Partition, Create Volume Set. However, if any disk fails, you cannot recover the file.
You can work around this situation with a program such as PartitionMagic, a hard disk management utility from PowerQuest. (For a description of this utility, see "PartitionMagic.") Because Microsoft encounters this In the Device list, expand Disk Drives. Consider removing all nonessential hardware drivers from the source computer before cloning, and then, after cloning, reinstalling the correct drivers on the destination computers. In such a situation, you have to use the emergency boot disk and boot from the mirrored disk and mirror the information on mirrored disk to a new disk.
Don't have a SymAccount? Partition Magic That is, Symantec Ghost 8.x and earlier, and Norton Ghost 2003 and earlier, do not support RAID controllers on computers that are being imaged. Update Ghost to the latest version. If you make all the free space an extended partition and then assign logical drives in the extended partition, you can remove the partition later, even with FDISK, a DOS-based hard
Click Start to initiate the format request. Once more, you must choose Commit Changes Now from the Partition menu to save your changes.Formatting a partition and labeling the volumeAfter you’ve created a partition and committed the changes, you In a disk array, the drives are coordinated into different levels of RAID, to which the controller card distributes the data. Encrypted files or folders on the source computer Windows NT/2000 cannot read encrypted files and directories when the SID has changed (after a rollout, Sysprep or Ghost Walker provides a new
Advertisement Recent Posts FUNCTION KEY MALFUNCTION bearspencer replied Mar 18, 2017 at 2:07 AM How do I update my bios? http://www.tomshardware.com/forum/5980-46-server-mirroring Establish Mirror creates the mirror set, using exactly as much space on the mirror drive as you assigned to the primary drive. Windows Nt Disk Management patmac replied Mar 18, 2017 at 12:33 AM Loading... Disk Administrator will also make all the partitions approximately the same size.
As you’ll see, Disk Administrator lets you:Create and delete partitions on a hard disk and logical drives within an extended partition.Format and label volumes.Read status information about disks, such as the Thanks for your registration, follow us on our social networks to keep up-to-date
A tape backup and restore is difficult because you need to run the restore under NT. All Rights Reserved. Just select the drive to mirror and, on a different physical disk, an area of free space that is at least as large. http://roguewb.com/windows-nt/windows-nt-repair-disk.html Also make sure that the drive has power and is connected properly.
I am doing this so that I can delete the partitions and go to a single partition so that I can mirror the disk with another one using Windows NT mirroring. Click Yes.On an Intel-based system, Windows NT will not let you delete the volume with the system files, nor can you delete individual partitions that are part of a set without Flush the old disk and mirror over the new disk to the old.
If you have SCSI drives, a low-level format will remove any existing partitions, but reformatting is a last resort. Note that if you use Ghost Console in Norton Ghost 6.04 Enterprise Edition, Symantec Ghost 6.5 Enterprise Edition, Symantec Ghost 7.0, Symantec Ghost 7.5, or Symantec Ghost 8.0 to clone to Tip explains how to get manually created replication connection objects in an Active Directory Forest... In these cases, Disk Administrator will inform you and not let you close out of Disk Administrator until you click OK to reboot.
Sign in here. Click Yes.At this point, Disk Administrator will display the minimum and maximum sizes for the primary partition. Click on the first area of free space, then hold down the Ctrl key and click each of the other areas. Sends shivers through my spine !
Keep in mind that establishing a stripe set, or a mirror set, and regenerating data can take some time, especially when the disks involved are very large. For instance, you might have one image file for a specific OEM HAL, another for a computer using IDE hard drives, and another for a different OEM HAL on a computer The catch is that volume sets must use the same disk type. Instead, you must delete the volumes on the dynamic disk and then change the disk back to a basic disk.
For Windows XP/Vista installations, use Microsoft's Sysprep tool on the source computer before cloning from that computer. For example, CD-ROM drives appear just like any other disk on a display. MS-DOS will identify the partitions of the mirror as "Non-DOS" partitions. Microsoft has an article discussing hardware differences between the source and destination computers when using Sysprep with Windows 2000.
Type the size of the stripe set you want to create, then click OK.Disk Administrator will divide the total size of the disks selected by the number of disks to create You can format the volume set as either FAT or NTFS. The backup needs to retain all the properties of the original file (ACLs, time, etc.).